Marathon Electric imPower Installationsanleitung

1 InstallationGuidewww.imPowerDealer.com

10 1110 11Single Speed Connection with Timer These steps as outlined below are for connection of the imPower motor to a single speed timer.Step 1:

10 1110 11Step 7: Carefully fold the extra wires inside the terminal box and place the top control panel back on top of the terminal box.Step 8: T

12 1312 133. The user can override the operational speed currently running via the buttons on the top control panel after the mandatory initial two

12 1312 13- 1 -Safety ConsiderationsThe following definitions are used as safety considerations on the Evergreen IM motor and in this manual. Please

14 1514 15Step 5: Remove the three screws holding the top control enclosure onto the motor. Carefully lift the top panel and turn it over to expos

14 1514 15Step 16: Replace the impeller. Make sure that the impeller can spin freely in the housing.Step 17: Replace the diuser.Step 18: Replac

16 1716 17Automation Controller Signal Line Connection The steps as outlined below are for connection of the imPower motor to an auto-mationcontrol

16 1716 17Step 9: Plugtheconnectorendofthelowvoltagecable(P/N391-200-01orP/N391-200-02)intotheconnectorontheundersideofthetop

18 1918 19Step 13: Wire the low voltage cable to the automation controller. The speed connectionsandtheircorrespondingleadcolorsareshownin

18 1918 19Notes:1. The automation controller allows for the programmable operation of all three speeds. The motor will start on high speed for e

2 32 3Marathon Electric oers a full line of motors for the pool, spa and bath markets. Poolside contractors prefer our pool and spa motors for the

20 2120 21Automatic Reduced Speed SelectionThe imPower motor has been programmed with a feature called the Automatic Reduced Speed Selection functio

20 2120 21Default Reduced Speed Operation:1. Forastandardsinglespeedtimerconnection,themotorwillrunhighspeed for the duration of the tw

22 2322 23Software Error Code MatrixThe imPower control panel has a red error display LED to indicate operation issues.Normaloperationisindica

22 2322 23Blinks Faults Software Cause Action6 Output shaft seizedMotor failed to start.Motor was stopped.- Manually rotate the shaft via the shaft

24 2524 25Troubleshooting Guide1. Issue: Motor will not automatically turn-down to the reduced speed after two hours when connected to a single sp

24 2524 255. Issue: Insucient ow from water features Action: Assuming this issue was not pre-existing, the programmed low speed on the imPower

26 2726 27Notes:

26 2726 27Notes:

28Need Additional imPower Help?Contractor Hotline:800-683-9144imPower Website:www.imPowerDealer.comRev 1.4 06/117032M/06-11/BHA Regal Beloit Company

2 32 3Table of Contents Safety Considerations 4 Introduction 6 Operation 7 Removing the Existing Motor from Pump 8 Topside Interface Ov

4 54 5Safety Considerations The following denitions are used as safety considerations on the imPower motor and in this manual. Please read and obse

4 54 5- 1 -Safety ConsiderationsThe following definitions are used as safety considerations on the Evergreen IM motor and in this manual. Please read

6 76 7Introduction The imPower motor is a permanent magnet alternating current (PMAC) electroni-cally commutated motor (ECM), leveraging over 20 yea

6 76 7Operation imPower motors are congured with Constant Speed, meaning they simply maintain the speed (RPM) they are congured for in each applic

8 98 9Remove the Existing Motor from PumpStep 1: Loosen and remove the screws holding the seal plate to the pump housing. Pull the seal plate / mo

8 98 9Topside Interface Overview The topside interface on the imPower motor provides functionality to change amongst three distinct preset speeds vi